Skip to content
Fluid Sealing Association® logo
Flow Systems partner

Fluid Sealing Association®

Fluid Sealing Association®

Founded in 1933, the FLUID SEALING ASSOCIATION® (FSA) is an international trade association. Member companies are involved in the production and marketing of a wide range of fluid sealing devices primarily targeted to the industrial market. FSA membership includes a number of companies in Europe and Central and South America, but is most heavily concentrated in North America. FSA members account for a majority of the manufacturing capacity for fluid sealing devices in the Americas market.

Our Mission is to be recognized as the primary source of technical information; to influence and support the development of related standards and to provide education in the fluid sealing area. To promote a safe, clean environment for society and a safe work place for our employees. To monitor the economic, environmental and social changes which may impact our membership’s business and to maintain a forum for the exchange of this information.

 


Published here

From Fluid Sealing Association®

Articles 13

See All Articles by Fluid Sealing Association®

White Papers

  • Buffer & Barrier FluidsRegister to download

    Author: Mark Savage, FSA Member As operators of pumping equipment become more focused on the safety, reliability and environmental impact resulting from shaft seal leakage, dual mechanical seals have become more prevalent in the industry. A dual mechanical seal offers a second (outer) seal to contain the pumped fluid by creating a cavity or chamber between the inner and outer seal that can be filled with a fluid. When this fluid is unpressurized, it forms a buffer between the pumped fluid and atmosphere and is commonly referred to as a buffer fluid. When pressurized, it forms a barrier between the pumped fluid and atmosphere and is known as a barrier fluid. Although mechanical seal designs are available in configurations that use either a liquid or a gas as a barrier fluid, the following discussion focuses on liquid buffer and barrier fluids only. In addition to separating the pumped fluid from the atmosphere, liquid buffer and barrier fluids lubricate the mechanical seal and transport frictional heat and absorbed heat from the mechanical seal to a heat exchanger. This controls the fluid’s temperature and lubricating properties.

  • Figure 1. Typical pump and mechanical seal arrangement Almost all centrifugal and rotary pumps require a sealing system to provide sealing integrity of the drive shafts carrying the impellers and protect against pumped fluid leakage and the environment outside of the wetted areas. These sealing systems range from traditional braided materials packed around the shaft to complex mechanical seal systems used in many modern pumps. Download this Fluid Sealing Association whitepaper to learn more.

  • Water and wastewater treatment is not a glamorous or popular topic. However, it is a critical part of our everyday lives that is often taken for granted. For example, the last thing on anyone’s mind during a major sporting event, such as the Super Bowl, is water and wastewater. During halftime, though, thousands of treatment facilities handle the demand when millions of people use their facilities at the same time. Municipal treatment facilities are sophisticated operations that use chemical and biological processes to contain and convert dangerous waste into an environmentally safe and often reusable material. Since most of these facilities are operated and funded by a municipal governing body, cost control, efficiency and reliability are top priorities. The review of common applications, rotating equipment and sealing options found in a typical treatment facility is important.

  • The Internet of Things (IoT) is a phrase in the limelight. The concept of IoT is extremely appealing, in all forms, to the commercial industry. The technology of IoT has been implemented in various industries globally and it is finally approaching the rotating equipment industry. To fully explain and understand how IoT technology can be implemented to increase mechanical seal reliability, a description of maintenance philosophies is needed. There are three main types of maintenance philosophies in industry today: reactive, preventative and predictive. Currently in the pump industry, and more specifically with mechanical seals, most of the maintenance is either in the reactive or preventative ideologies. This is where the current model of IoT comes into play. IoT is a powerful tool that will enable the industry to progress to a predictive maintenance model. This is accomplished by using advanced technology in several key areas such as device connectivity, data storage, and cutting-edge analytics.

  • Learn how different metals react, and how corrosion inhibitors can help avoid downtime. By Brittany Kelley, A.W. Chesterton Valve packing is a necessity for plants trying to contain product and meet the latest emission requirements. However, finding a sealing product that works and has longevity can be a challenge. Graphite-based packing can be a good choice for stem sealing when elevated temperature requirements are necessary. This is due to graphite’s ability to maintain its sealing properties at temperatures that cause polytetrafluoroethylene (PTFE) to break down and allow leaks to occur. However, graphite is not an electrical insulator like PTFE; graphite will act as a metal and undergo galvanic corrosion if the environment is right. Download to read more!

  • Author: Phil Mahoney FSA Member, A.W. Chesterton Co. Currently, two test procedures could be requested to qualify a quarter-turn valve design for fugitive emissions service: International Standards Organization (ISO) 15848-1 (2nd Edition, 2015) and American Petroleum Institute (API) 641 (1st edition, 2016). Both standards are technically viable options that can be used for valve qualification. Both could be considered good engineering practice since they clearly spell out conditions and procedures that help ensure the test is repeatable, and that it can be considered representative of the valve’s real life operating conditions. Download this whitepaper paper by Phil Mahoney; an FSA Member, from A.W. Chesterton Co.; to learn more about International Standards Organization and American Petroleum Institute.

  • Author: Henri Azibert, FSA Member The use of variable speed drives (VSD) has become increasingly more prevalent in an effort to improve the energy efficiency of pumping systems. Efficiency is improved through the ability of the VSD to adjust the rotational speed of a rotodynamic pump and match its hydraulic characteristics to those of the system in which it operates. Whether the mismatch was due to the variation in required pump output or incorrect sizing of the pump, there is no question that the ability to easily vary pump speed has been a major advance in the overall performance of a pumping system. This has increased energy efficiency, as well as the reliability of the equipment. Problems—such as cavitation or shaft deflection—can be alleviated by running the pump at optimal system speed. But how do VSDs affect mechanical seals?

  • Contributor: Mark Freeman FSA Member, EGC Enterprises, Inc. The American Petroleum Institute (API) has developed two commonly used standards designed specifically for the petroleum industry. They include API 622 “Type Testing of Process Valve Packing for Fugitive Emissions,” and API 624 “Type Testing of Rising Stem Valves Equipped with Graphite Packing for Fugitive Emissions.” API 622 and API 624 may be specified by an end-user. Valve OEMs must use API 622-approved packing for any valve on test for API 624. Download this whitepaper from Fluid Sealing Association! Image 1 (left). Testing fixtureImage 2 (right). Thermo toxic vapor analyzer (Image courtesy of Yarmouth Research)

  • Contributor: Fluid Sealing Association In today’s world, facilities face the daunting challenge of minimizing the environmental impact of industrial processes. A primary motivation for industrial plants to control their environmental impact is government regulation. In the U.S., these regulations are issued at the national level by the Environmental Protection Agency (EPA) and similar agencies at the state and local levels. Before the U.S. government passed the first Clean Air Act in 1963, no federal regulations on gaseous emissions existed. The Clean Air Act initiated research to investigate techniques to monitor and control air pollution. During the 1970s and 1980s, the government passed legislation that established a limit on emissions of 10,000 parts per million (ppm) for gases defined as volatile hazardous air pollutants (VHAPs). Similarly in Europe, a series of accidents resulting in toxic chemical release lead to adoption of the European Commission directive 82/501/EEC targeting safety measures to prevent the release of hazardous chemicals. This threshold came down to 1,000 ppm in the 1990s. In some cases, these emissions restrictions were driven even lower by local authorities. The sealing industry has always worked to provide innovative solutions to meet the goals of the regulations and industry.

  • This is the last of a four-part “Sealing Sense” series that has provided guidance on the best practices to minimize the size of the sealing system energy footprint. The first article discussed the energy losses from the interaction between the faces of a mechanical seal while the second discussed the thermal energy required to maintain the proper temperature of the interfacial lubricating fluid. The third article detailed the thermal energy footprint necessary to remove diluents introduced by auxiliary processes. This final article will address the energy footprint from repairing a pump after a leak in the sealing system required intervention. Time to fix the leak

  • This whitepaper from the Fluid Sealing Association provides guidance on best practices to minimize the size of the sealing system energy footprint. The first article discussed the energy losses from the interaction between the faces of a mechanical seal. The second discussed the thermal energy required to maintain the proper temperature of the interfacial lubricating fluid. We will now discuss the thermal energy footprint of removing diluents introduced by auxiliary processes. A flush is often added to the stuffing box or mechanical seal chamber. This helps to extend seal life by displacing solids, removing the heat generated by packing or a mechanical seal, and heat soak from the seal chamber. The flush fluid then becomes mixed with the process fluid as a diluent that may need to be removed from the process fluid. Figure 1. API Piping Plan 32—energy lost through dilution and vaporization

  • In this whitepaper from the Fluid Sealing Association, this piece provides guidance on best practices to minimize the size of the sealing system energy footprint. Authored by Eric Vanhie, EagleBurgmann, Member of the FSA, this article discusses the thermal energy needed to maintain a suitable temperature for the interfacial lubricating fluid in high-temperature processes.

  • The term carbon footprint has become synonymous with greenhouse gas (GHG) emissions and climate change. Carbon footprint commonly refers to the volume of greenhouse gases, the most prominent of which is carbon dioxide, which are emitted by an organization, event, process or product. Because of climate change concerns, coupled with rising energy costs and dependency on non-renewable and foreign sources of energy, the related term energy footprint is entering the vernacular of industry and regulatory organizations. The U.S. Department of Energy (DOE) developed energy footprints to help target energy saving opportunities in the manufacturing industry. They map the flow of energy supply and demand in facilities and show where and how the energy was used and lost from inefficiencies. The DOE uses energy footprint maps such as the one in Figure 1 to track the flow of energy supply, demand and losses. Figure 2. Seal face lubrication regimes

  • Whenever there is a decision to be made regarding an investment in equipment or systems to make operating cost improvements, companies typically want to know if the up-front investment to achieve the improvements is worth the cost and risk of making the investment. Three common methods to evaluate the financial implications of the various improvement options are: Simple payback Discounted payback Internal rate of return (IRR) analysis In this 3-page whitepaper from Thomas E. Haan, Principal, Global Equity Consulting, LLC, he educates us about these methods of evaluation of the benefits of making investments to improve MTBR and enhance the energy efficiency of equipment and systems.

  • Pumping fluids at extreme temperatures presents many challenges to the shaft sealing system. It must ensure the pumped fluid is safely contained while providing long-term reliability. Many pump operators are familiar with hot pumping services, but cold services offer some unique challenges to achieving reliable shaft sealing solutions. In this 5-page technical whitepaper from Fluid Sealing Association, you will learn about: Pumping Equipment for Low Temperature Hydrocarbons Seal Selection for Low Temperature Hydrocarbons Material Considerations for Low Temperature Hydrocarbons Pumping Equipment for Liquefied Atmospheric Gases Seal Selection for Liquefied Atmospheric Gases Material Considerations for Liquefied Atmospheric Gases

  • There are many methods to pressurize the barrier fluid for a dual pressurized mechanical seal. Each method, or piping plan, uses a different mechanism to apply the pressure to the barrier fluid and, as a result, each has its own set of advantages. One of these methods is American Petroleum Institute (API) Plan 53C. Although not as widely installed as a traditional API Plan 53A system, it does differentiate itself from other methods. API Plan 53C has the ability to change the barrier pressure as the pressure inside the pump changes. This pressure tracking ability makes this system ideally suited to highpressure pumps, or for pumps that tend to experience a wide range of operating pressures. Image 1 (left). Simplified Plan 53C schematic. Image 2 (center). Typical piston accumulator. Image 3 (right). Piston face areas (Images courtesy of FSA) A Plan 53C barrier system consists of two main elements: Barrier fluid circulating loop: A pumping device within the mechanical seal circulates barrier fluid to a heat exchanger, where heat absorbed into the barrier fluid is dissipated and then the fluid is returned to the mechanical seal. • Piston accumulator: Stores barrier fluid and amplifies pressure from the pump to pressurize the barrier fluid circulating loop.

  • In this technical whitepaper from Fluid Sealing Association Member, Richard Albery, Senior Gas Seal Engineer at John Crane, learn about how to seal high-speed shafts in pumps and compressors.

  • Figure 1. Typical cartridge seal The challenges facing process industries have changed although they continue to pump fluids, some hazardous or toxic. Safety and reliability are still of prime importance. However, operators increase speeds, pressures, flow rates and even the severity of the fluid characteristics (temperature, concentration, viscosity, etc.) while processing many batch operations. For the operators of petroleum refineries, gas processing facilities and petrochemical and chemical plants, safety means controlling and preventing loss of, or exposure to, the pumped fluids. Reliability means pumps that operate efficiently and economically, with less required maintenance. A properly designed mechanical seal assures a pump operator of long-lasting, safe and reliable pump performance with a proven technology. Among multiple pieces of rotating equipment and a myriad of components, mechanical seals are proven to perform dependably under most types of operating conditions.

Request information

Ask Fluid Sealing Association®

Questions about a product, a quote or a spec? Send your request and we pass it to the right contact at Fluid Sealing Association®.

Loading the request form